{"product_id":"gm74-orange-gasket-maker-sealant-50ml","title":"GM74 - Orange Gasket Maker \/ Sealant 50ml","description":"Orange Gasket Maker \/ Sealant 50ml\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eA high viscosity thixotropic gel, which cures rapidly, sealing instantly to 10 bar through its Anaerobic cure system, in contact with Metals in the absence of air (oxygen). When fully cured it resists pressure up to 200 bar and up to 180°C.\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eApplications\u003cbr data-mce-fragment=\"1\"\u003eTypical applications are in sealing all types of flat faced surfaces with close fits against water, oil, gases and most common materials conveyed by systems needing sealing.\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eDirections for use\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eParts should be clean, dry and dust free.\u003cbr data-mce-fragment=\"1\"\u003eDegreased parts will assist results.\u003cbr data-mce-fragment=\"1\"\u003eApply sufficient product to fill joint.\u003cbr data-mce-fragment=\"1\"\u003eAssemble parts in traditional manner.\u003cbr data-mce-fragment=\"1\"\u003eTo achieve handling strength allow product to cure (approximately 15 minutes).\u003cbr data-mce-fragment=\"1\"\u003eStore in cool conditions.\u003cbr data-mce-fragment=\"1\"\u003eKeep out of direct sunlight.\u003cbr data-mce-fragment=\"1\"\u003eWhere cure speed is extended due to low temperatures or inactive surfaces, activator can be used (not supplied).\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eBest results are found if the sealant is applied in a continuous bead avoiding blind holes etc. Excess can be wiped away. Any migration into lines will not solidify and can be flushed away during commissioning.\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eProperties\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eFast Cure to fixture usually \u0026lt;30 minutes @ 20°C on steel. Temperature Range: -50°C to + 180°C\u003cbr data-mce-fragment=\"1\"\u003eTypical Break-loose: 12Nm. up to 18Nm (ISO method 4) Typical Strength: 6 N.m prevailing on M10’s (ISO method 4) Recommended for flat faced assemblies with near zero gaps. Increase of gap size or fit extends the cure time.\u003cbr data-mce-fragment=\"1\"\u003eAn activator (Standard anaerobic activator) can be used, however, up to 30% strength loss can occur when using accelerators.\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e \u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eTechnical Data\u003cbr data-mce-fragment=\"1\"\u003eChemical base: Methacrylate Ester\u003cbr data-mce-fragment=\"1\"\u003eColour: Orange \/ Fluorescent\u003cbr data-mce-fragment=\"1\"\u003eSpecific Gravity @ 25°C: 1.05 @ 200C\u003cbr data-mce-fragment=\"1\"\u003eViscosity (25°C): 75000 – 90000 mPas @ 250C (Brookfield Spindle 6 @10rpm):\u003cbr data-mce-fragment=\"1\"\u003eFlashpoint: \u0026gt;1000C\u003cbr data-mce-fragment=\"1\"\u003eMax.Gap Fill: 0.50 mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e \u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eCured Performance @23°C - Measured on M10 x 20 bolt – grade 8.8 zinc galvanised – nut 0.8d loose free running (1) (2) (3) ISO method is loose M10’s mild steel no on torque (4)\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003eInitial strength: 20 – 30 minutes\u003cbr data-mce-fragment=\"1\"\u003eFunctional strength: 1 – 3 hours\u003cbr data-mce-fragment=\"1\"\u003eFinal strength: 12 – 24 hours\u003cbr data-mce-fragment=\"1\"\u003eBreak-loose torque: 12 – 20 N.m (M10) DIN*\u003cbr data-mce-fragment=\"1\"\u003ePrevailing torque: 6 – 14 N.m (M10) DIN*\u003cbr data-mce-fragment=\"1\"\u003eShear strength: 6 – 13 N\/mm2 DIN5445\u003cbr data-mce-fragment=\"1\"\u003e\u003cbr data-mce-fragment=\"1\"\u003e","brand":"Grease Monkey Direct","offers":[{"title":"Default Title","offer_id":44585083699490,"sku":"GT-LS228","price":5.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1359\/2999\/products\/ls228.600.jpg?v=1651748747","url":"https:\/\/greasemonkeydirect.co.uk\/products\/gm74-orange-gasket-maker-sealant-50ml","provider":"Grease Monkey Direct","version":"1.0","type":"link"}